AIRWAAV RECOVERY RX1 MOUTHPIECE

STEP 1: PROTECT

Roll up part of a dripping wet paper towel and place it in between the channels of the mouthpiece to help prevent the walls from folding when heating the mouthpiece.

STEP 2: COVER

Cover the plate with a dripping wet paper towel and place the AIRWAAV in the middle of the plate with the side walls of the mouthpiece facing up. Cover the AIRWAAV performance mouthpiece by folding up the soaked paper towel.

STEP 3: MICROWAVE

Place the plate in the microwave and heat for 1 minute and 30 seconds. (Add more time if needed based on microwave power level)

STEP 4: RETRIEVE AND DUNK

Remove the mouthpiece from the plate, loosen the paper towel covering the mouthpiece, remove the rolled-up paper towel and drop the mouthpiece directly into the bowl of cold water (please use caution the paper towel and mouthpiece could be very hot). Allow the mouthpiece to rest in the bowl of cold water for 3-5 seconds.

STEP 5: MOLD

While looking into a mirror, carefully place the AIRWAAV on your bottom teeth and avoid the sidewalls from closing in by having your teeth placed in the center of the bite channel. The mouthpiece will be in the correct position once the front intake Bar is sitting behind your front lower teeth. The front Intake Bar should not be on top of your lower front teeth. Once the mouthpiece is in the correct position, mold by:

STEP 6: RECHARGE YOUR POTENTIAL

After at least 5 minutes of molding the AIRWAAV in your mouth, place the molded device back in cold water for 30 seconds to solidify the material. It is recommended to wait 24 hours after the molding step before using the mouthpiece, as AIRWAAV's patented fitting material will continue to shrink and proivde a tighter fit during that time.

After 24 hours, the AIRWAAV mouthpiece will be ready to use.

STEP 1: BOIL

Fill a pot with enough water so that the mouthpiece can be submerged without touching the bottom of the pot and heat on a stove.

STEP 2: DROP

Once the water is boiling, turn off the heat and drop the mouthpiece into the boiling water. Leave the mouthpiece in the water for one minute.

STEP 3: RETRIEVE & DUNK

Retrieve the mouthpiece using a slotted spoon and drop it directly into the bowl of cold water. Allow the mouthpiece to rest in the bowl of cold water for 3-5 seconds.

STEP 4: MOLD

While looking into a mirror, carefully place the AIRWAAV on your bottom teeth and avoid the sidewalls from closing in by having your teeth placed in the center of the bite channel. The mouthpiece will be in the correct position once the front intake Bar is sitting behind your front lower teeth. The front Intake Bar should not be on top of your lower front teeth. Once the mouthpiece is in the correct position, mold by:

STEP 5: COOL

After 5 minutes of molding the AIRWAAV in your mouth, place the molded device back in cold water for 5 minutes to solidify the material. It is recommended to wait 24 hours after the molding step before using the mouthpiece, as AIRWAAV's patented fitting material will continue to shrink and provide a tighter fit during that time.

STEP 6: RECHARGE YOUR POTENTIAL

After at least 5 minutes of molding the AIRWAAV in your mouth, place the molded device back in cold water for 30 seconds to solidfiy the material. It is recommended to wait 24 hours after the molding step before using the mouthpiece, as AIRWAAV's patented fitting material will continue to shrink and proivde a tighter fit during that time.

After 24 hours, the AIRWAAV mouthpiece will be ready to use.

The AIRWAAV RECOVERY Mouthpiece can transform the way you recover. After the initial adaptation phase, you'll notice how it improves your quality of sleep.

Remember, everyone's journey is unique. The AIRWAAV RECOVERY Mouthpiece is here to support and enhance your recovery at any level, and with consistent use you will be on your way to supercharging your recovery.